Planar Microwave Sensor with High Sensitivity for Material Characterization Based on Square Split Ring Resonator (SSRR) for Solid and Liquid
Abstract
Microwave resonator sensors are the most extensively used sensors in the food industries, quality assurance, medical, and manufacturing. Planar resonant technique is chosen as the medium for characterizing dielectric properties of material due to its compact in size, low cost and easy to fabricate. But these techniques have a low Q-factor and little sensitivity. This work uses the perturbation approach to overcome this technique's flaw, which is that Q-factor and resonant frequency are affected by the resonator's dielectric properties. This suggested sensor operated at 2.5GHz between 1GHz and 4GHz for material characterisation of solid and liquid samples. These sensors were constructed on a substrate made of RT/Duroid Roger 5880, which has a copper layer that is 0.0175 mm thick and has a dielectric constant of 2.2. This square split ring resonator (SSRR) sensor thus generates narrower resonant, low insertion loss, and a high Q-factor value of 430 at 2.5GHz. The SSRR sensor's sensitivity is 98.59%, which is higher than that of past studies. The application of the suggested sensor as a tool for material characterisation, particularly for identifying material attributes, is supported by this findings.
Downloads
References
Al-Behadili, A.A. et al. , Modified split ring resonators sensor for accurate complex permittivity measurements of solid dielectrics, Sensors (Switzerland), 2020 20(23), pp. 1–18. doi:10.3390/s20236855. DOI: https://doi.org/10.3390/s20236855
Al-behadili, A.A., Petrescu, T. and Mocanu, I.A. , Complimentary split ring resonator sensor with high sensitivity based on material characterization’, Telkomnika (Telecommunication Computing Electronics and Control), 2020 18(1), pp. 272–281. doi:10.12928/TELKOMNIKA.v18i1.13255. DOI: https://doi.org/10.12928/telkomnika.v18i1.13255
Alahnomi, R.A. et al. , Enhanced symmetrical split ring resonator for metallic surface crack detection’, Telkomnika (Telecommunication Computing Electronics and Control), 2019, 17(4), pp. 2107–2115. doi:10.12928/TELKOMNIKA.v17i4.12939. DOI: https://doi.org/10.12928/telkomnika.v17i4.12939
Narayanan PM, Microstrip transmission line method for broadband permittivity measurement of dielectric substrates, IEEE Trans. Microw. Theory Tech, 2014;62:2784–90. DOI: https://doi.org/10.1109/TMTT.2014.2354595
Alhegazi, A. et al. , Analysis and investigation of a novel microwave sensor with high Q-factor for liquid characterization’, Telkomnika (Telecommunication Computing Electronics and Control), 2019, 17(2), pp. 1065–1070. doi:10.12928/TELKOMNIKA.V17I2.11901. DOI: https://doi.org/10.12928/telkomnika.v17i2.11901
Amiruddin, A.A.M., Abdullah, N. and Mohd, E. , Development of split ring resonator for pineapple moisture content detection’, Bulletin of Electrical Engineering and Informatics, 2021, 10(5), pp. 2636–2642. doi:10.11591/eei.v10i5.2828. DOI: https://doi.org/10.11591/eei.v10i5.2828
Mohd Bahar AA, Zakaria Z, Md. Arshad MK, Isa AAM, Dasril Y, Alahnomi RA, Real Time Microwave Biochemical Sensor Based on Circular SIW Approach for Aqueous Dielectric Detection. Sci. Rep, [Internet] 2019;9:1–12, Available from: http://dx.doi.org/10.1038/s41598-019-41702-3. DOI: https://doi.org/10.1038/s41598-019-41702-3
Islam, R. et al. , Metamaterial sensor based on rectangular enclosed adjacent triple circle split ring resonator with good quality factor for microwave sensing application’, Scientific Reports, 2022, pp. 1–18. doi:10.1038/s41598-022-10729-4. DOI: https://doi.org/10.1038/s41598-022-10729-4
Ivanov, A. et al. , Design and characterization of a microwave planar sensor for dielectric assessment of vegetable oils’, Electronics (Switzerland), 2019, 8(9), pp. 1–9. doi:10.3390/electronics8091030. DOI: https://doi.org/10.3390/electronics8091030
Ismail, M.K. et al. , Microwave planar sensor for determination of the permittivity of dielectric material’, Bulletin of Electrical Engineering and Informatics, 2018, 7(4), pp. 640–649. doi:10.11591/eei.v7i4.1355. DOI: https://doi.org/10.11591/eei.v7i4.1355
Jang, S.-Y. and Yang, J.-R. , Double Split-Ring Resonator for Dielectric Constant Measurement of Solids and Liquids’, Journal of Electromagnetic Engineering and Science, 2022, 22(2). doi:10.26866/jees.2022.2.r.68. DOI: https://doi.org/10.26866/jees.2022.2.r.68
Lee, G.H. et al. , Generalized Design Technique of Ultra-Wideband Transitions for Quasi-TEM Planar Transmission Lines Based on Analytical Models’, IEEE Access, 2021, 9, pp. 52619–52633. doi:10.1109/ACCESS.2021.3069870. DOI: https://doi.org/10.1109/ACCESS.2021.3069870
Iqbal A, Smida A, Saraereh OA, Alsafasfeh QH, Mallat NK, Lee BM, Cylindrical dielectric resonator antenna-based sensors for liquid chemical detection, Sensors (Switzerland), 2019;19:2–10. DOI: https://doi.org/10.3390/s19051200
Yeo J, Lee JI, Slot-loaded microstrip patch sensor antenna for high-sensitivity permittivity characterization, Electron, 2019;8. DOI: https://doi.org/10.3390/electronics8050502
Ma, J. et al. , Complex permittivity characterization of liquid samples based on a split ring resonator (SRR)’, Sensors, 2021, 21(10). doi:10.3390/s21103385. DOI: https://doi.org/10.3390/s21103385
Mahashabde, S. et al. , Fast Tunable High- Q -Factor Superconducting Microwave Resonators’, Physical Review Applied, 2020, 10(1), p. 1. doi:10.1103/PhysRevApplied.14.044040. DOI: https://doi.org/10.1103/PhysRevApplied.14.044040
Muñoz-Enano, J. et al. , Planar microwave resonant sensors: A review and recent developments’, Applied Sciences (Switzerland), 2020, 10(7). doi:10.3390/app10072615. DOI: https://doi.org/10.3390/app10072615
Oliveira, J.G.D. et al. , CSRR-based microwave sensor for dielectric materials characterization applied to soil water content determination’, Sensors (Switzerland), 2020, 20(1). doi:10.3390/s20010255. DOI: https://doi.org/10.3390/s20010255
Rahman, N.A. et al. , Dual band planar microwave sensor for dielectric characterization using solid and liquid sample’, Journal of Telecommunication, Electronic and Computer Engineering, 2018, 10(2–8), pp. 27–32.
Raveendran, A. et al. , Complex Permittivity Extraction of Planar Dielectrics Using a Noninvasive Microwave Transmission Line Resonant Technique’, 2021, 70. DOI: https://doi.org/10.1109/TIM.2021.3070614
Reyes-Vera, E. et al. , A submersible printed sensor based on a monopole-coupled split ring resonator for permittivity characterization’, Sensors (Switzerland), 2019, 19(8). doi:10.3390/s19081936. DOI: https://doi.org/10.3390/s19081936
Shahzad, W. et al. , A Low-Cost Metamaterial Sensor Based on DS-CSRR for Material Characterization Applications’, Sensors, 2022, 22(5), pp. 1–11. doi:10.3390/s22052000. DOI: https://doi.org/10.3390/s22052000
Sobkiewicz, P., Bieńkowski, P. and Błażejewski, W. , Microwave non‐destructive testing for delamination detection in layered composite pipelines’, Sensors, 21(12), 2021. doi:10.3390/s21124168. DOI: https://doi.org/10.3390/s21124168
Su, L. et al. , Analytical method to estimate the complex permittivity of oil samples’, Sensors (Switzerland), 2018, 18(4), pp. 1–12. doi:10.3390/s18040984. DOI: https://doi.org/10.3390/s18040984
Pozar D, Microwave Engineering Fourth Edition. John Wiley & Sons Ltd, 2005.
Wang, C. et al. , A Sensor for Characterisation of Liquid Materials with High Permittivity and High Dielectric Loss’, Sensors, 2022, 22(5), pp. 1–14. doi:10.3390/s22051764. DOI: https://doi.org/10.3390/s22051764
Xu, K. et al. , Novel Microwave Sensors Based on Split Ring Resonators for Measuring Permittivity’, IEEE Access, 2018, 6(c), pp. 26111–26120. doi:10.1109/ACCESS.2018.2834726. DOI: https://doi.org/10.1109/ACCESS.2018.2834726
Zahertar, S., Dodd, L.E. and Torun, H. , Embroidered Rectangular Split-Ring Resonators for Material Characterisation’, FLEPS 2019 - IEEE International Conference on Flexible and Printable Sensors and Systems, Proceedings, 2019, 2, pp. 2–4. doi:10.1109/FLEPS.2019.8792233. DOI: https://doi.org/10.1109/FLEPS.2019.8792233
Zapata-Londoño, J. et al. , Differential microwave sensor based on microstrip lines loaded with a split-ring resonator for dielectric characterization of materials’, Journal of Physics: Conference Series, 2118(1), 2021. doi:10.1088/1742-6596/2118/1/012004. DOI: https://doi.org/10.1088/1742-6596/2118/1/012004
Copyright (c) 2023 EMITTER International Journal of Engineering Technology
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
The copyright to this article is transferred to Politeknik Elektronika Negeri Surabaya(PENS) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to PENS. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment. The copyright transfer form can be downloaded here .
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
- Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
- Authors may reproduce or authorize others to reproduce the work or derivative works for the author’s personal use or company use, provided that the source and the copyright notice of Politeknik Elektronika Negeri Surabaya (PENS) publisher are indicated.
- Authors are allowed to use and reuse their articles under the same CC-BY-NC-SA license as third parties.
- Third-parties are allowed to share and adapt the publication work for all non-commercial purposes and if they remix, transform, or build upon the material, they must distribute under the same license as the original.
Plagiarism Check
To avoid plagiarism activities, the manuscript will be checked twice by the Editorial Board of the EMITTER International Journal of Engineering Technology (EMITTER Journal) using iThenticate Plagiarism Checker and the CrossCheck plagiarism screening service. The similarity score of a manuscript has should be less than 25%. The manuscript that plagiarizes another author’s work or author's own will be rejected by EMITTER Journal.
Authors are expected to comply with EMITTER Journal's plagiarism rules by downloading and signing the plagiarism declaration form here and resubmitting the form, along with the copyright transfer form via online submission.